New IT forum
25 June 2022, 11:10:11 pm *
Welcome, %1$s. Please login or register.

: CubieBoard 2 and Cubietruck both now in stock.
 
Pages: [1]

Author Topic: initial Bootlog  (Read 4630 times)

NewIT_Malcolm

  • Administrator
  • Jr. Member
  • *****
  • Posts: 65
initial Bootlog
« on: 24 August 2012, 09:22:55 am »

Initial Bootlog, notice it downloading patches at the end of the boot sequence.


Code: [Select]
 
        __  __                       _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____                _
| | | |   | __ )  ___   ___ | |_
| | | |__|  _ \ / _ \ / _ \| __|
| |_| | _| |_) | (_) | (_) | |_
 \___/   |____/ \___/ \___/ \__|
 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Sep 13 2011 - 13:25:05) Marvell version: 3.4.27
USISH-SMB Ver: topkick1281p2-001-008-20110913-codelathe

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006D0120

Soc: MV88F1155 Rev 1 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM unknown CAL  tRP = 8 tRAS = 20 tRCD=8
DRAM CS[0] base 0x00000000   size 512MB
DRAM Total size 512MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  3 \0x08\0x08\0x08 2 \0x08\0x08\0x08 1 \0x08\0x08\0x08 0
(Re)start USB...
USB:   scanning bus for devices... 1 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
0 Storage Device(s) found
** Bad partition 1 **
## Booting image at 00800000 ...
Bad Magic Number
Saving Environment to NAND...
Erasing Nand...Writing to Nand... done

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found

** Bad partition 1 **
## Booting image at 00800000 ...
Bad Magic Number
Saving Environment to NAND...
Erasing Nand...Writing to Nand... done

NAND read: device 0 offset 0x200000, size 0x600000


Reading data from 0x200000 --   0% complete.
Reading data from 0x20f000 --   1% complete.
Reading data from 0x21e800 --   2% complete.
Reading data from 0x22e000 --   3% complete.
Reading data from 0x23d000 --   4% complete.
Reading data from 0x24c800 --   5% complete.
..
..
..
Reading data from 0x7e1000 --  98% complete.
Reading data from 0x7f0800 --  99% complete.
Reading data from 0x7ff800 -- 100% complete.
 6291456 bytes read: OK
## Booting image at 01200000 ...
   Image Name:   Linux-2.6.31.8-topkick1281p2-001
   Created:      2011-11-10   3:58:11 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3121408 Bytes =  3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

Linux version 2.6.31.8-topkick1281p2-001-004-20101214 ([email protected]) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #2 Thu Nov 10 11:58:07 CST 2011
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line: console=ttyS0,115200;version=topkick1281p2-001-006-20101103 mtdparts=nand_mtd:[email protected](u-boot),[email protected](u-boot-env),[email protected](uImage),[email protected](rootfs) ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rootdelay=10
PID hash table entries: 2048 (order: 11, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512MB = 512MB total
Memory: 513280KB available (5612K code, 319K data, 148K init, 0K highmem)
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 794.62 BogoMIPS (lpj=3973120)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
xor: measuring software checksum speed
   arm4regs  :   723.200 MB/sec
   8regs     :   433.600 MB/sec
   32regs    :   600.800 MB/sec
xor: using function: arm4regs (723.200 MB/sec)
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 512MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e8000000, size 128MB
PEX0_IO ....base f2000000, size   1MB
INTER_REGS ....base f1000000, size   1MB
NFLASH_CS ....base fa000000, size   2MB
SPI_CS ....base f4000000, size  16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size   2MB

  Marvell Development Board (LSP Version KW_LSP_5.0.3)-- DB-88F6282A-BP  Soc: MV88F1155 Rev 1 LE

 Detected Tclk 200000000 and SysClk 400000000
MV Buttons Device Load
Marvell USB EHCI Host controller #0: df837740
PEX0 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
raid6: int32x1     72 MB/s
raid6: int32x2    101 MB/s
raid6: int32x4     88 MB/s
raid6: int32x8     80 MB/s
raid6: using algorithm int32x2 (101 MB/s)
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
rtc mv_rtc: rtc core: registered kw-rtc as rtc0
RTC registered
cpufreq: Init kirkwood cpufreq driver
XOR registered 4 channels
XOR 2nd invalidate WA enabled
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Warning: TS unit is powered off.
MV Buttons Driver Load
JFFS2 version 2.2. (NAND) \0xc2\0xa9 2001-2006 Red Hat, Inc.
SGI XFS with security attributes, large block/inode numbers, no debug enabled
msgmni has been set to 1002
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
alg: No test for hmac(digest_null) (hmac(digest_null-generic))
async_tx: api initialized (sync-only)
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
Loading Marvell Ethernet Driver:
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o 2 Giga ports supported
  o Multi RX Queue support - 4 RX queues
  o Multi TX Queue support - 2 TX Queues
  o TCP segmentation offload (TSO) supported
  o Large Receive offload (LRO) supported
  o Receive checksum offload supported
  o Transmit checksum offload supported
  o Network Fast Processing (Routing) supported - (Disabled)
  o Network Fast Processing (NAT) supported
  o Driver ERROR statistics enabled
  o Driver INFO statistics enabled
  o Proc tool API enabled
  o SKB Reuse supported - (Disabled)
  o SKB Recycle supported - (Disabled)
  o Gateway support enabled
     o Using Marvell Header Mode
     o L2 IGMP support
  o Rx descripors: q0=128 q1=128 q2=128 q3=128
  o Tx descripors: q0=532 q1=532
  o Loading network interface(s):
    o  register under mv88fx_eth platform
    o eth0, ifindex = 2, GbE port = 0

Warning: Giga 1 is Powered Off

Warning: Giga 1 is Powered Off

mvFpRuleDb (df280000): 16384 entries, 65536 bytes
Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI
Copyright (c) 1999-2006 Intel Corporation.
e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
e1000e: Copyright (c) 1999-2008 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
Using Hamming 1-bit ECC for NAND device
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 1069 at 0x0000085a0000
Bad eraseblock 1424 at 0x00000b200000
Bad eraseblock 1792 at 0x00000e000000
Bad eraseblock 1793 at 0x00000e020000
Bad eraseblock 2576 at 0x000014200000
Bad eraseblock 3807 at 0x00001dbe0000
4 cmdlinepart partitions found on MTD device nand_mtd
Using command line partition definition
Creating 4 MTD partitions on "nand_mtd":
0x000000000000-0x000000180000 : "u-boot"
0x000000180000-0x0000001a0000 : "u-boot-env"
0x000000200000-0x000000800000 : "uImage"
0x000000800000-0x000020000000 : "rootfs"
UBI: attaching mtd3 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd3 to ubi0
UBI: MTD device name:            "rootfs"
UBI: MTD device size:            504 MiB
UBI: number of good PEBs:        4026
UBI: number of bad PEBs:         6
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             81
UBI: total number of reserved PEBs: 3945
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 2/1
UBI: image sequence number: 0
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
UBI: background thread "ubi_bgt0d" started, PID 472
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
pwrctl: dev_t_NO. = 0xdd00000, major = 221
pwrctl: request the irq power off registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Linux telephony interface: v1.00
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [email protected]
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
Advanced Linux Sound Architecture Driver Version 1.0.20.
No device for DAI CS42L51
ALSA device list:
  No soundcards found.
nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
mvFpNatDb (df360000): 16384 entries, 65536 bytes
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
NFP (fdb) init 256 entries, 1024 bytes
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
All bugs added by David S. Miller <[email protected]>
rtc mv_rtc: setting system clock to 2012-08-24 17:08:16 UTC (1345828096)
Waiting 10sec before mounting root device...
mmc0: new high speed SDIO card at address 0001
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size:   501387264 bytes (489636 KiB, 478 MiB, 3886 LEBs)
UBIFS: journal size:       25159680 bytes (24570 KiB, 23 MiB, 195 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root:  4952683 bytes (4836 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:11.
Freeing init memory: 148K
Using makefile-style concurrent boot in runlevel S.
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
Setting parameters of disc: (none).
Activating swap...done.
Starting early crypto disks...done.
Starting remaining crypto disks...done.
Loading kernel modules...done.
Cleaning up ifupdown....
Setting up networking....
Activating lvm and md swap...done.
Checking file systems...fsck from util-linux-ng 2.17.2
done.
Mounting local filesystems...done.
Activating swapfile swap...done.
Cleaning up temporary files....
Setting kernel variables ...done.
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.1.1-P1
Copyright 2004-2010 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

eth0: link up, full duplex, speed 1 Gbps
eth0: started
Listening on LPF/eth0/40:2c:f4:bc:93:fa
Sending on   LPF/eth0/40:2c:f4:bc:93:fa
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
DHCPOFFER from 192.168.1.254
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 192.168.1.254
Reloading /etc/samba/smb.conf: smbd onlyNo process in pidfile '/var/run/samba/smbd.pid' found running; none killed.
.
bound to 192.168.1.75 -- renewal in 352834 seconds.
done.
Cleaning up temporary files....
fuse init (API version 7.12)
init: rc-sysinit main process (515) killed by TERM signal

Using makefile-style concurrent boot in runlevel 2.
Network Interface Plugging Daemon...start eth0...done.
Starting enhanced syslogd: rsyslogd.
Starting periodic command scheduler: cron.
Starting system message bus: dbus.
Starting Samba daemons: nmbd smbd.
Starting OpenBSD Secure Shell server: sshd.

Debian GNU/Linux 6.0 TonidoPlug2 ttyS0

TonidoPlug2 login: wget: ./libcrypto.so.0.9.8: no version information available (required by wget)
wget: ./libssl.so.0.9.8: no version information available (required by wget)
--2012-08-24 17:08:46--  http://patch.codelathe.com/firmware/tonidoplug2/updates.list
Resolving patch.codelathe.com... 50.97.134.197
Connecting to patch.codelathe.com|50.97.134.197|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 44
Saving to: \0xe2\0x80\0x9cplugscripts/update/updates.list\0xe2\0x80\0x9d


 0% [                                       ] 0           --.-K/s             
100%[======================================>] 44          --.-K/s   in 0s     

2012-08-24 17:08:47 (1.20 MB/s) - \0xe2\0x80\0x9cplugscripts/update/updates.list\0xe2\0x80\0x9d saved [44/44]

wget: ./libcrypto.so.0.9.8: no version information available (required by wget)
wget: ./libssl.so.0.9.8: no version information available (required by wget)
--2012-08-24 17:08:47--  http://patch.codelathe.com/firmware/tonidoplug2/update_0.3.1.1.tgz
Resolving patch.codelathe.com... 50.97.134.197
Connecting to patch.codelathe.com|50.97.134.197|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 133056 (130K) [application/x-gzip]
Saving to: \0xe2\0x80\0x9cplugscripts/update/update_0.3.1.1.tgz\0xe2\0x80\0x9d


 0% [                                       ] 0           --.-K/s             
18% [======>                                ] 24,190      77.5K/s             
57% [=====================>                 ] 76,030       146K/s             
100%[======================================>] 133,056      192K/s   in 0.7s   

2012-08-24 17:08:48 (192 KB/s) - \0xe2\0x80\0x9cplugscripts/update/update_0.3.1.1.tgz\0xe2\0x80\0x9d saved [133056/133056]

wget: ./libcrypto.so.0.9.8: no version information available (required by wget)
wget: ./libssl.so.0.9.8: no version information available (required by wget)
--2012-08-24 17:08:48--  http://patch.codelathe.com/firmware/tonidoplug2/update_0.3.1.1.md5
Resolving patch.codelathe.com... 50.97.134.197
Connecting to patch.codelathe.com|50.97.134.197|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 53
Saving to: \0xe2\0x80\0x9cplugscripts/update/update_0.3.1.1.md5\0xe2\0x80\0x9d


 0% [                                       ] 0           --.-K/s             
100%[======================================>] 53          --.-K/s   in 0s     

2012-08-24 17:08:48 (1.48 MB/s) - \0xe2\0x80\0x9cplugscripts/update/update_0.3.1.1.md5\0xe2\0x80\0x9d saved [53/53]

Logged
Pages: [1]
 
 

Powered by MySQL Powered by PHP SMF 2.0.10 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!