Print

[bigbear59]

A power cycle should get it back or poke the reset button

[Jimbob]

No output from fdisk -l

I've powered it off and back on and I'm back at the Marvell prompt.

[bigbear59]

You did a fdisk -l (lower case L) after plugging the USB onto another Linux system?

[Jimbob]

Yes mate.

[Jimbob]

[email protected]:~$ fdisk -l
[email protected]:~$

[bigbear59]

try
/sbin/fdisk -l

[Jimbob]

[email protected]:~$ /sbin/fdisk -l
[email protected]:~$

[bigbear59]

strange , try
which fdisk
lsusb

[Jimbob]

Result:

Bus 002 Device 014: ID 9e88:9e8f 
Bus 002 Device 005: ID 0409:005a NEC Corp. HighSpeed Hub
Bus 002 Device 018: ID 03f0:3407 Hewlett-Packard
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 002: ID 044e:3001 Alps Electric Co., Ltd UGTZ4 Bluetooth
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 003: ID 15ca:00c3 Textech International Ltd. Mini Optical Mouse
Bus 005 Device 002: ID 04d9:1503 Holtek Semiconductor, Inc. Shortboard Lefty
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

[bigbear59]

Well at least it shows up in lsusb
  Bus 002 Device 018: ID 03f0:3407 Hewlett-Packard
Do you have another USB that you can format fat16?
and put uImage on then plug into the Plug?

[Jimbob]

Not here but I can get one later today. It's 6am here in the UK, doesn't look like I'm going to get any sleep. I'll go and get one when the shops are open. Thanks for all your help I will keep you posted

I have an SD Card if that would work?

[bigbear59]

You can try the SD, The SD shows up on the Sheeva as a mmc
so it would be
mmcinit; fatload mmc 0 0x800000 /uImage; bootm 0x800000

but as a last try on the USB change the address to 0x800000
so usb start; fatload usb 0 0x800000 uImage;bootm 0x800000

[Jimbob]

Marvell>> usb start; fatload usb 0 0x800000 uImage;bootm 0x800000
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
reading uImage
Invalid FAT entry

221184 bytes read
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-2.6.30.2
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2620440 Bytes = 2.5 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
Marvell>>

[Jimbob]

Same from SD Card:

Marvell>> mmcinit; fatload mmc 0 0x800000 /uImage; bootm 0x800000
Unknown command 'mmcinit' - try 'help'

** Unable to use mmc 0:1 for fatload **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-2.6.30.2
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2620440 Bytes = 2.5 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
Marvell>>

[Jimbob]

Is the installer I downloaded corrupted?